[ 0.000000] Linux version 5.15.0-starfive (sw_buildbot@mdcsw02) (riscv64-unknown-linux-gnu-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #1 SMP Mon Feb 27 14:03:14 EST 2023
[ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000
[ 0.000000] Machine model: StarFive VisionFive V2
[ 0.000000] earlycon: uart0 at MMIO32 0x0000000010000000 (options '115200')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000023fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff]
[ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff]
[ 0.000000] node 0: [mem 0x00000000c0200000-0x000000023fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff]
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10002
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] SBI SRST extension detected
[ 0.000000] SBI v0.2 HSM extension detected
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] riscv: ISA extensions acdfim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] percpu: Embedded 17 pages/cpu s31528 r8192 d29912 u69632
[ 0.000000] pcpu-alloc: s31528 r8192 d29912 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
[ 0.000000] Kernel command line: root=/dev/mmcblk1p4 rw console=tty0 console=ttyS0,115200 earlycon rootwait stmmaceth=chain_mode:1 selinux=0
[ 0.000000] Unknown command line parameters: stmmaceth=chain_mode:1 selinux=0
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
[ 0.000000] Memory: 7581776K/8386560K available (9963K kernel code, 4983K rwdata, 4096K rodata, 2191K init, 401K bss, 280496K reserved, 524288K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller
[ 0.000000] riscv-intc: 64 local interrupts mapped
[ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts.
[ 0.000000] random: get_random_bytes called from start_kernel+0x4d0/0x6e2 with crng_init=0
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns
[ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns
[ 0.008997] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.020321] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.031652] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.042975] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.054469] Console: colour dummy device 80x25
[ 0.060703] printk: console [tty0] enabled
[ 0.065257] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000)
[ 0.076481] pid_max: default: 32768 minimum: 301
[ 0.081773] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.090254] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.100551] ASID allocator disabled
[ 0.104490] rcu: Hierarchical SRCU implementation.
[ 0.109941] EFI services will not be available.
[ 0.115331] smp: Bringing up secondary CPUs ...
[ 0.121960] smp: Brought up 1 node, 4 CPUs
[ 0.128393] devtmpfs: initialized
[ 0.139894] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.150756] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.172093] pinctrl core: initialized pinctrl subsystem
[ 0.178751] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.185987] cpuidle: using governor menu
[ 0.211761] platform soc:dsi-output: Fixing up cyclic dependency with 29400000.dc8200
[ 0.220935] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsi-output
[ 0.229774] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000.dc8200
[ 0.250409] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.257793] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.268467] vgaarb: loaded
[ 0.271694] SCSI subsystem initialized
[ 0.276084] libata version 3.00 loaded.
[ 0.276261] usbcore: registered new interface driver usbfs
[ 0.282340] usbcore: registered new interface driver hub
[ 0.288235] usbcore: registered new device driver usb
[ 0.294077] mc: Linux media interface: v0.10
[ 0.298824] videodev: Linux video capture interface: v2.00
[ 0.305055] Advanced Linux Sound Architecture Driver Initialized.
[ 0.312162] Bluetooth: Core ver 2.22
[ 0.316126] NET: Registered PF_BLUETOOTH protocol family
[ 0.321982] Bluetooth: HCI device and connection manager initialized
[ 0.328981] Bluetooth: HCI socket layer initialized
[ 0.334366] Bluetooth: L2CAP socket layer initialized
[ 0.339935] Bluetooth: SCO socket layer initialized
[ 0.345650] clocksource: Switched to clocksource riscv_clocksource
[ 0.360037] NET: Registered PF_INET protocol family
[ 0.366411] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.382371] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
[ 0.392127] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.401702] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[ 0.411897] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.419416] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 0.427310] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[ 0.436041] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.442944] RPC: Registered named UNIX socket transport module.
[ 0.449495] RPC: Registered udp transport module.
[ 0.454671] RPC: Registered tcp transport module.
[ 0.459857] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.467677] PCI: CLS 0 bytes, default 64
[ 0.472671] Initialise system trusted keyrings
[ 0.477815] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 0.478004] Unpacking initramfs...
[ 0.490960] NFS: Registering the id_resolver key type
[ 0.496575] Key type id_resolver registered
[ 0.501190] Key type id_legacy registered
[ 0.505735] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.513125] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.521351] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.526457] jffs2: version 2.2. (NAND) \xc2\xa9 2001-2006 Red Hat, Inc.
[ 0.533656] fuse: init (API version 7.34)
[ 0.577677] NET: Registered PF_ALG protocol family
[ 0.582991] Key type asymmetric registered
[ 0.587560] Asymmetric key parser 'x509' registered
[ 0.593043] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.601241] io scheduler mq-deadline registered
[ 0.606254] io scheduler kyber registered
[ 0.616024] start plist test
[ 0.618736] end plist test
[ 0.711650] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 clkgen init successfully.
[ 0.722948] L2CACHE: DataError @ 0x00000000.08040140
[ 0.728512] L2CACHE: DataFail @ 0x00000000.0804005B
[ 0.733974] L2CACHE: No. of Banks in the cache: 8
[ 0.739185] L2CACHE: No. of ways per bank: 16
[ 0.743995] L2CACHE: Sets per bank: 256
[ 0.748248] L2CACHE: Bytes per cache block: 64
[ 0.753159] L2CACHE: Index of the largest way enabled: 15
[ 0.759449] jh7110-pmu 17030000.power-controller: registered 8 power domains
[ 0.828153] Serial: driver, 6 ports, IRQ sharing disabled
[ 0.838184] @@#########################@@
[ 0.880600] @@ dev ptr:ffffffe0bff00000/1500/1
[ 0.885785] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers
[ 0.893057] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system
[ 0.903297] [drm] Initialized pvr 1.17.6210866 20170530 for 18000000.gpu on minor 0
[ 0.921246] loop: module loaded
[ 0.927321] spi-nor spi0.0: gd25lq128d (16384 Kbytes)
[ 1.208244] Freeing initrd memory: 9848K
[ 1.230226] 3 fixed-partitions partitions found on MTD device 13010000.spi.0
[ 1.238058] Creating 3 MTD partitions on "13010000.spi.0":
[ 1.244120] 0x000000000000-0x000000020000 : "spl"
[ 1.251043] 0x000000100000-0x000000400000 : "uboot"
[ 1.258000] 0x000000f00000-0x000001000000 : "data"
[ 1.265978] libphy: Fixed MDIO Bus: probed
[ 1.271965] CAN device driver interface
[ 1.276813] starfive-eth-plat 16030000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[ 1.288219] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[ 1.296498] starfive-eth-plat 16030000.ethernet: DWMAC4/5
[ 1.302549] starfive-eth-plat 16030000.ethernet: DMA HW capability register supported
[ 1.311199] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine supported
[ 1.319843] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported
[ 1.327332] starfive-eth-plat 16030000.ethernet: TSO supported
[ 1.333764] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.342997] starfive-eth-plat 16030000.ethernet: Enabled Flow TC (entries=1)
[ 1.350780] starfive-eth-plat 16030000.ethernet: TSO feature enabled
[ 1.357792] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width
[ 1.618729] libphy: stmmac: probed
[ 1.622506] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 1.633470] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 1.645665] starfive-eth-plat 16040000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[ 1.657073] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[ 1.665330] starfive-eth-plat 16040000.ethernet: DWMAC4/5
[ 1.671401] starfive-eth-plat 16040000.ethernet: DMA HW capability register supported
[ 1.680044] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine supported
[ 1.688687] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported
[ 1.696175] starfive-eth-plat 16040000.ethernet: TSO supported
[ 1.702606] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.711838] starfive-eth-plat 16040000.ethernet: Enabled Flow TC (entries=1)
[ 1.719618] starfive-eth-plat 16040000.ethernet: TSO feature enabled
[ 1.726632] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width
[ 1.986790] libphy: stmmac: probed
[ 1.990568] YT8531 Gigabit Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_addr=stmmac-1:00, irq=POLL)
[ 2.001530] YT8531 Gigabit Ethernet stmmac-1:01: attached PHY driver (mii_bus:phy_addr=stmmac-1:01, irq=POLL)
[ 2.014040] Intel(R) Wireless WiFi driver for Linux
[ 2.021383] cdns3-starfive 10210000.usbdrd: usb mode 2 2.0 probe success
[ 2.029583] usbcore: registered new interface driver uas
[ 2.035487] usbcore: registered new interface driver usb-storage
[ 2.055998] starfive-rtc 17040000.rtc: registered as rtc0
[ 2.061964] starfive-rtc 17040000.rtc: setting system clock to 2001-01-01T00:00:00 UTC (978307200)
[ 2.072016] i2c_dev: i2c /dev entries driver
[ 2.076990] usbcore: registered new interface driver uvcvideo
[ 2.084552] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=180000000 (0aba9500)
[ 2.094312] Bluetooth: HCI UART driver ver 2.3
[ 2.099238] Bluetooth: HCI UART protocol H4 registered
[ 2.105121] starfive-cpufreq soc:starfive,jh7110-cpufreq: Failed to get regulator for cpu!
[ 2.114266] starfive-cpufreq soc:starfive,jh7110-cpufreq: Failed to init starfive cpu dvfs info
[ 2.124426] sdhci: Secure Digital Host Controller Interface driver
[ 2.131262] sdhci: Copyright(c) Pierre Ossman
[ 2.136113] Synopsys Designware Multimedia Card Interface Driver
[ 2.143053] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.150137] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel in DMA channel
[ 2.159288] jh7110-sec 16000000.crypto: Cannot initial dma chan
[ 2.166121] usbcore: registered new interface driver usbhid
[ 2.172272] usbhid: USB HID core driver
[ 2.176768] usbcore: registered new interface driver snd-usb-audio
[ 2.191400] NET: Registered PF_PACKET protocol family
[ 2.197031] can: controller area network core
[ 2.201946] NET: Registered PF_CAN protocol family
[ 2.207255] can: raw protocol
[ 2.210528] can: broadcast manager protocol
[ 2.215149] can: netlink gateway - max_hops=1
[ 2.220326] Bluetooth: RFCOMM TTY layer initialized
[ 2.225742] Bluetooth: RFCOMM socket layer initialized
[ 2.231437] Bluetooth: RFCOMM ver 1.11
[ 2.235608] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.241484] Bluetooth: BNEP filters: protocol multicast
[ 2.247267] Bluetooth: BNEP socket layer initialized
[ 2.252802] lib80211: common routines for IEEE802.11 drivers
[ 2.259053] lib80211_crypt: registered algorithm 'NULL'
[ 2.259068] lib80211_crypt: registered algorithm 'WEP'
[ 2.259081] lib80211_crypt: registered algorithm 'CCMP'
[ 2.259094] lib80211_crypt: registered algorithm 'TKIP'
[ 2.259229] 9pnet: Installing 9P2000 support
[ 2.264007] Key type dns_resolver registered
[ 2.269499] Loading compiled-in X.509 certificates
[ 2.311252] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registered 64 GPIOs
[ 2.320895] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registered 4 GPIOs
[ 2.329877] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels
[ 2.337786] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels
[ 2.347369] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' already present!
[ 2.356546] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 23
[ 2.364562] ssp-pl022 10060000.spi: ARM PL022 driver for StarFive SoC platform, device ID: 0x00041022
[ 2.374767] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to (____ptrval____)
[ 2.384912] ssp-pl022 10060000.spi: Requested frequency: 10000000 Hz is unsupported,select by default 8250000 Hz
[ 2.396534] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms
[ 2.406423] i2c 2-0045: Fixing up cyclic dependency with 295d0000.mipi
[ 2.413893] seeed_panel 2-0045: Unknown Atmel firmware revision: 0x00
[ 2.421200] tinker-ft5406: tinker_ft5406_probe: address = 0x38
[ 2.427662] tinker-ft5406: tinker_ft5406_probe: width = 800, height = 480, reverse = 1
[ 2.436562] tinker-ft5406: fts_i2c_read: i2c read error, -121
[ 2.442897] tinker-ft5406: tinker_ft5406_probe: checking touch ic failed
[ 2.450305] tinker_ft5406: probe of 2-0038 failed with error -121
[ 2.457232] i2c 2-0019: Fixing up cyclic dependency with 295d0000.mipi
[ 2.465864] at24 5-0050: supply vcc not found, using dummy regulator
[ 2.473660] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[ 2.483016] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900 ~ 900 mV
[ 2.493166] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:1800 ~ 1800 mV
[ 2.503502] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900 ~ 900 mV
[ 2.513670] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 ~ 1540 mV
[ 2.523103] i2c 6-0010: Fixing up cyclic dependency with 19800000.vin_sysctl
[ 2.531290] imx219 6-0010: supply VANA not found, using dummy regulator
[ 2.538729] imx219 6-0010: supply VDIG not found, using dummy regulator
[ 2.546119] imx219 6-0010: supply VDDL not found, using dummy regulator
[ 2.560897] imx219 6-0010: failed to read chip id 219
[ 2.566702] imx219: probe of 6-0010 failed with error -5
[ 2.575123] pcie_plda 2b000000.pcie: host bridge /soc/pcie@2B000000 ranges:
[ 2.582896] pcie_plda 2b000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0x0030000000
[ 2.591852] pcie_plda 2b000000.pcie: MEM 0x0900000000..0x093fffffff -> 0x0900000000
[ 2.600833] ATR entry: 0x0940000000 -> 0x0000000000 [0x0010000000] (param: 0x000001)
[ 2.609404] ATR entry: 0x0030000000 -> 0x0030000000 [0x0008000000] (param: 0x000000)
[ 2.617967] ATR entry: 0x0900000000 -> 0x0900000000 [0x0040000000] (param: 0x000000)
[ 2.975749] pcie_plda 2b000000.pcie: Port link up.
[ 2.981194] pcie_plda 2b000000.pcie: PCI host bridge to bus 0000:00
[ 2.988129] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.994183] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 3.001784] pci_bus 0000:00: root bus resource [mem 0x900000000-0x93fffffff pref]
[ 3.010076] pci 0000:00:00.0: [1556:1111] type 01 class 0x060400
[ 3.016721] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0xffffffff 64bit pref]
[ 3.024750] pci 0000:00:00.0: supports D1 D2
[ 3.029469] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.040285] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.049272] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[ 3.055928] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[ 3.063493] pci 0000:01:00.0: PME# supported from D0 D3cold
[ 3.072976] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.080315] pci 0000:00:00.0: BAR 0: no space for [mem size 0x100000000 64bit pref]
[ 3.088785] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x100000000 64bit pref]
[ 3.097638] pci 0000:00:00.0: BAR 8: assigned [mem 0x30000000-0x300fffff]
[ 3.105121] pci 0000:01:00.0: BAR 0: assigned [mem 0x30000000-0x30000fff 64bit]
[ 3.113214] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 3.118698] pci 0000:00:00.0: bridge window [mem 0x30000000-0x300fffff]
[ 3.126306] pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 3.132548] pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 3.138853] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x9d4 took 12262 usecs
[ 3.147247] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 3.153029] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 3.161619] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000040000000890
[ 3.171779] pcie_plda 2b000000.pcie: msi#0 address_hi 0x0 address_lo 0x190
[ 3.179754] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 3.185530] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 3.193719] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 3.201358] hub 1-0:1.0: USB hub found
[ 3.205532] hub 1-0:1.0: 1 port detected
[ 3.210998] hub 2-0:1.0: USB hub found
[ 3.215185] hub 2-0:1.0: 4 ports detected
[ 3.222448] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges:
[ 3.230213] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000
[ 3.239191] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[ 3.248204] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0x000001)
[ 3.256772] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0x000000)
[ 3.265321] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0x000000)
[ 3.425696] usb usb2-port2: over-current condition
[ 3.525721] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 3.585729] usb usb2-port4: over-current condition
[ 3.695912] pcie_plda 2c000000.pcie: Port link down, exit.
[ 3.715699] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7110 clk_vout init successfully.
[ 3.727599] hub 1-1:1.0: USB hub found
[ 3.731983] hub 1-1:1.0: 4 ports detected
[ 3.738132] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH7110 clk_isp init successfully.
[ 3.749357] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels
[ 3.760376] printk: console [ttyS0] disabled
[ 3.785312] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 17, base_baud = 1500000) is a 16550A
[ 3.795162] printk: console [ttyS0] enabled
[ 3.803967] printk: bootconsole [uart0] disabled
[ 3.814198] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter!
[ 3.822340] jh7110-vin 19800000.vin_sysctl: stfcamss probe success!
[ 3.831065] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mode.
[ 3.831468] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mode.
[ 3.831698] jh7110-sec 16000000.crypto: will run requests pump with realtime priority
[ 3.834904] jh7110-sec 16000000.crypto: Initialized
[ 3.836026] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported
[ 3.836037] starfive-i2s 120b0000.i2stx_4ch0: designware: i2s master mode supported
[ 3.836208] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin
[ 3.836222] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 445
[ 3.836345] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO
[ 3.836369] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator
[ 3.836652] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end
[ 3.836836] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000
[ 3.837067] cdns-dsi 295d0000.mipi: starfive dsi bind end
[ 3.838401] dwmmc_starfive 16010000.sdio0: Using internal DMA controller.
[ 3.845685] dwmmc_starfive 16020000.sdio1: Using internal DMA controller.
[ 3.853501] dwmmc_starfive 16010000.sdio0: Version ID is 290a
[ 3.853545] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 29,32 bit host data width,32 deep fifo
[ 3.856941] of_cfs_init
[ 3.856981] of_cfs_init: OK
[ 3.857491] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac_apb = 49500000, clk_pwmdac_core = 4068493
[ 3.857928] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.858424] dwmmc_starfive 16020000.sdio1: Version ID is 290a
[ 3.865367] mmc_host mmc0: card is non-removable.
[ 3.873032] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 30,32 bit host data width,32 deep fifo
[ 3.990871] mmc_host mmc1: card is polling.
[ 3.995767] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 4.004872] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xffffffff80e75d38)
[ 4.013180] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin
[ 4.019795] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 4.028448] cfg80211: failed to load regulatory.db
[ 4.033939] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success
[ 4.044030] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done.
[ 4.050592] innohdmi-starfive 29590000.hdmi: inno hdmi bind end
[ 4.056537] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xffffffff80e76ae8)
[ 4.064637] vs-simple-encoder soc:dsi-output: encoder_bind begin
[ 4.070678] no panel, -517
[ 4.073391] vs-simple-encoder soc:dsi-output: encoder_bind error
[ 4.079410] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffffffff80e76730)
[ 4.088003] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsystem on minor 1
[ 4.105683] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248)
[ 4.205771] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248)
[ 4.458799] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 50000000Hz, actual 49500000HZ div = 2)
[ 4.468902] mmc1: new high speed SDXC card at address 5048
[ 4.476338] mmcblk1: mmc1:5048 SD128 119 GiB
[ 4.483271] random: fast init done
[ 4.491021] Alternate GPT is invalid, using primary GPT.
[ 4.496429] mmcblk1: p1 p2 p3 p4
[ 4.555743] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000Hz, actual 300000HZ div = 330)
[ 4.995717] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000Hz, actual 200000HZ div = 495)
[ 5.445762] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000Hz, actual 100000HZ div = 990)
[ 6.165733] ALSA device list:
[ 6.168754] #0: Starfive-PWMDAC-Sound-Card
[ 6.173080] #1: Starfive-HDMI-Sound-Card
[ 6.182238] Freeing unused kernel image (initmem) memory: 2188K
[ 6.188550] Run /init as init process
[ 6.192268] with arguments:
[ 6.192283] /init
[ 6.192296] with environment:
[ 6.192311] HOME=/
[ 6.192323] TERM=linux
[ 6.192337] stmmaceth=chain_mode:1
[ 6.192355] selinux=0
[ 6.745434] starfive-eth-plat 16030000.ethernet end0: renamed from eth0
[ 6.847350] starfive-eth-plat 16040000.ethernet end1: renamed from eth1
[ 7.113471] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled.
[ 7.812166] systemd[1]: System time before build time, advancing clock.
[ 7.892887] systemd[1]: systemd 252.4-1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 7.924998] systemd[1]: Detected architecture riscv64.
[ 7.936808] systemd[1]: Hostname set to <starfive>.
[ 8.513141] systemd[1]: Queued start job for default target Graphical Interface.
[ 8.523145] systemd[1]: Created slice Slice /system/getty.
[ 8.529609] systemd[1]: Created slice Slice /system/modprobe.
[ 8.536911] systemd[1]: Created slice Slice /system/serial-getty.
[ 8.543989] systemd[1]: Created slice User and Session Slice.
[ 8.551005] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 8.559954] systemd[1]: Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc).
[ 8.577401] systemd[1]: Reached target Local Integrity Protected Volumes.
[ 8.585516] systemd[1]: Reached target Remote File Systems.
[ 8.592355] systemd[1]: Reached target Slice Units.
[ 8.598689] systemd[1]: Reached target Swaps.
[ 8.604408] systemd[1]: Reached target Local Verity Protected Volumes.
[ 8.612474] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 8.626765] systemd[1]: Journal Audit Socket was skipped because of an unmet condition check (ConditionSecurity=audit).
[ 8.638337] systemd[1]: Listening on Journal Socket (/dev/log).
[ 8.645497] systemd[1]: Listening on Journal Socket.
[ 8.651898] systemd[1]: Listening on udev Control Socket.
[ 8.658476] systemd[1]: Listening on udev Kernel Socket.
[ 8.666674] systemd[1]: Mounting Huge Pages File System...
[ 8.674865] systemd[1]: Mounting POSIX Message Queue File System...
[ 8.684149] systemd[1]: Mounting Kernel Debug File System...
[ 8.690955] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[ 8.705071] systemd[1]: Create List of Static Device Nodes was skipped because of an unmet condition check (ConditionFileNotEmpty=/lib/modules/5.15.0-starfive/modules.devname).
[ 8.723970] systemd[1]: Starting Load Kernel Module configfs...
[ 8.732643] systemd[1]: Starting Load Kernel Module drm...
[ 8.740921] systemd[1]: Starting Load Kernel Module efi_pstore...
[ 8.749762] systemd[1]: Starting Load Kernel Module fuse...
[ 8.760124] systemd[1]: Starting Journal Service...
[ 8.770778] systemd[1]: Starting Load Kernel Modules...
[ 8.779492] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 8.786656] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
[ 8.799535] systemd[1]: Starting Coldplug All udev Devices...
[ 8.810035] systemd[1]: Mounted Huge Pages File System.
[ 8.817195] systemd[1]: Mounted POSIX Message Queue File System.
[ 8.824405] systemd[1]: Mounted Kernel Debug File System.
[ 8.831660] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 8.839352] systemd[1]: Finished Load Kernel Module configfs.
[ 8.853670] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 8.861456] systemd[1]: Finished Load Kernel Module drm.
[ 8.868497] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[ 8.876677] systemd[1]: Finished Load Kernel Module efi_pstore.
[ 8.883895] systemd[1]: Started Journal Service.
[ 8.927096] systemd-journald[246]: Received client request to flush runtime journal.
[ 8.946849] systemd-journald[246]: File /var/log/journal/594f0bf7214947fabb5c4c6a67c52e4e/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 9.553404] systemd-journald[246]: Oldest entry in /var/log/journal/594f0bf7214947fabb5c4c6a67c52e4e/system.journal is older than the configured file retention duration (1month), suggesting rotation.
[ 9.553434] systemd-journald[246]: /var/log/journal/594f0bf7214947fabb5c4c6a67c52e4e/system.journal: Journal header limits reached or header out-of-date, rotating.
[ 10.088242] random: avahi-daemon: uninitialized urandom read (4 bytes read)
[ 10.088609] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[ 10.493968] venc: loading out-of-tree module taints kernel.
[ 10.522022] vdec 130a0000.vpu_dec: device init.
[ 10.522043] SUCCESS alloc_chrdev_region
[ 10.536768] SUCCESS alloc_chrdev_region
[ 10.608533] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[ 10.610044] cnm_jpu 13090000.jpu: init device.
[ 11.103957] random: alsactl: uninitialized urandom read (4 bytes read)
[ 11.598672] random: alsactl: uninitialized urandom read (4 bytes read)
[ 11.700163] random: wpa_supplicant: uninitialized urandom read (4096 bytes read)
[ 11.735687] random: crng init done
[ 13.366691] starfive-eth-plat 16030000.ethernet end0: PHY [stmmac-0:00] driver [YT8531 Gigabit Ethernet] (irq=POLL)
[ 13.377905] starfive-eth-plat 16030000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 13.386256] dwmac4: Master AXI performs fixed burst length
[ 13.391786] starfive-eth-plat 16030000.ethernet end0: No Safety Features support found
[ 13.399789] starfive-eth-plat 16030000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported
[ 13.409358] starfive-eth-plat 16030000.ethernet end0: configuring for phy/rgmii-id link mode
[ 13.422531] vs_gem_dumb_create size = 1000
[ 13.426707] Allocated coherent memory, vaddr: 0xFFFFFFE1FB3FF600, paddr: 0x1014C0000
[ 13.434457] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0
[ 13.450029] starfive-eth-plat 16040000.ethernet end1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL)
[ 13.460728] starfive-eth-plat 16040000.ethernet end1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 13.475666] dwmac4: Master AXI performs fixed burst length
[ 13.481174] starfive-eth-plat 16040000.ethernet end1: No Safety Features support found
[ 13.489212] starfive-eth-plat 16040000.ethernet end1: IEEE 1588-2008 Advanced Timestamp supported
[ 13.502444] starfive-eth-plat 16040000.ethernet end1: configuring for phy/rgmii-id link mode
[ 13.797298] PVR_K: 413: RGX Firmware image 'rgx.fw.36.50.54.182' loaded
[ 13.883990] PVR_K: 413: Shader binary image 'rgx.sh.36.50.54.182' loaded
[ 13.896908] PVR_K: 413: X connected - (devID = 0)
[ 14.083389] vs_gem_dumb_create size = 300000
[ 14.088685] Allocated coherent memory, vaddr: 0xFFFFFFE1F97BDC00, paddr: 0x80200000
[ 14.096400] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0
[ 14.115413] vs_gem_dumb_create size = 4000
[ 14.119662] Allocated coherent memory, vaddr: 0xFFFFFFE1F97BA5C0, paddr: 0x80108000
[ 14.127336] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0
[ 14.133085] vs_gem_dumb_create size = 4000
[ 14.137305] Allocated coherent memory, vaddr: 0xFFFFFFE1F97BA6A0, paddr: 0x8010C000
[ 14.144961] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0
[ 15.537884] starfive-eth-plat 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 34.486091] mipi_0p9: disabling
[ 348.325629] starfive-eth-plat 16030000.ethernet end0: Link is Down
[ 350.408029] starfive-eth-plat 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 364.965590] starfive-eth-plat 16030000.ethernet end0: Link is Down
[ 367.048004] starfive-eth-plat 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 370.165404] starfive-eth-plat 16030000.ethernet end0: Link is Down
[ 371.208031] starfive-eth-plat 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 376.405621] starfive-eth-plat 16030000.ethernet end0: Link is Down
[ 378.488005] starfive-eth-plat 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx